Condition : 100% Brand New, Exactly the same as seen in pictures. Fitment Type: Direct Replacement. Left, Right, Front, Rear. Kit or Single Part. Shock Aborber? Boot? Bumper Kit? Spring Seat? Coil Spring? Isolator. Material:Iron, Aluminium Alloy, Rubber. 2PC Part Front Left and Right Complete Spring Struts. 2PC Rear Left and Right Shock Absorbers. Guaranteed Exact Fit for easy installation. 100% BRAND NEW and tested to meet or exceed OEM specifications. These are brand new, not used or junkyard parts. High corrosion resistance and long service life. Steel rod is mirco-polished with double chrome plate. Newer Valving technology operates in stages based on the velocity of the car. Use Teflon bonded piston seal to keep friction down and temperature cooler so that valving stays firmer. All-around welding on the spring seat. Includes all of the following (where applicable): strut/shock, coil spring, strut/shock mount, boot, bumper kit, spring seat and isolator. These are guaranteed exact fit and don’t require the use of a dangerous spring compressor to swap springs, so they are very easy to install! The struts/shocks are nitrogen gas charged and tuned for each specific vehicle application. Step 1: Before you lift the vehicle, loosen lug nuts one full turn. Step 2: Jack up vehicle and use jack stands for safety & remove the tire from the rotor. Step 3: Wheel alignment is necessary after strut replacement. Marking the position of all the bolts will help keep the alignment close to original and save time aligning. Use a colored pencil to mark the old strut on the bolt. Step 4: Use penetrating oil to coat any rusted fasteners, let soak for approximately 1 hour. Step 5: (Optional) While waiting for oil to soak, take this time to inspect all other components that may need replacement (brake pads, rotors, brake hoses, ball joints, CV boots, tie rod ends, bushings, sway bars, etc). Step 6: Remove any brake line or wire attachments from the strut body. Do not disconnect brake lines (if possible)! Opening brake lines will require bleeding of the brake system. Use extreme caution when removing brake lines from your struts, as any damage to your brake line can result in expensive and time consuming repairs. Step 7: Remove sway bar attached to the strut assembly or control arm. Step 8: Remove the tie rod (only if it attached to the body of the strut, if not leave it attached to the steering knuckle). Step 9: Remove the strut to knuckle bolts at the bottom of the strut. On some vehicles, the brake caliper and rotor may need to be removed to gain access. Step 10: Remove the upper mounting plate bolts located in the engine or trunk compartment. Do not remove the center retaining nut! It is not safe to unload the spring from the assembly in this position. Step 11: Carefully remove the old strut assembly from the vehicle. Be very cautious not to let the strut “drop” down on your brake line, rotor or drum. Step 12: Install the new Complete Strut Assembly in the reverse order as above (steps 11-6). Using an anti-seize compound on all fasteners is suggested. Step 13: Carefully double check your work and make sure everything is tightened to manufacturers torque specifications. Step 14: Replace the tire the rotor and tighten to manufacturers torque specifications. Step 15: Slowly lower the vehicle down after removing the jack stands. Pay very close attention to any odd sounds when the vehicle is lowered onto the new Complete Strut Assemblies. Step 16: It is very important that you immediately “road test” your vehicle right away to ensure that installation was done properly. Listen and feel for common signs of incorrect installation while driving slowly over speed bumps, rough road or potholes. When the original car shock absorber is removed, the corresponding positions of the top rubber and spring should be marked first. When replacing the shock absorber, ensure that the top rubber and the original mark points of the spring are aligned. Failure to follow this operation may cause abnormal noise in the suspension system! Installing the top rubber should use special tools to manually install, remember not to use any tool to clamp the shock absorber piston rod (bright rod part), so as not to scratch the shock absorber piston rod, causing oil leakage. Do not use pneumatic or electric wrenches for the top glue installation to avoid slippage or damage to the shock absorber piston rod bolts. What shocks and struts do? You could say that their main job is to resist both tire and vehicle body motion. When shocks and struts are working well, the vehicle maintains traction on the road and has the optimum stability in every driving condition: stopping, turning, swerving, over bumps and potholes. Can I Drive With a Broken Strut? A strut is a suspension component that dampens an automobile’s movements and prevents it from bouncing on its springs. Struts are often expensive to replace, but driving on a broken strut is not a good idea. Can worn shocks or struts cause my new tires to wear unevenly? Absolutely: shocks and struts provide damping force to control tire movement. When the tires move excessively, they develop a “cupping” wear pattern that damages the tire. Other factors such as incorrect air pressure, worn suspension components or improperly aligned steering also causes uneven tire wear. Shall we choose to replace the normal shock absorber or the direct shock absorber assembly? From the perspective of the difficulty of replacement, it is difficult to replace an independent shock absorber, requires professional equipment and technicians, and has a high risk factor. From the price point of view, the individual parts of the shock absorber kit are expensive to replace, while the shock absorber assembly contains all the parts of the shock absorber system, which is cheaper than replacing all the parts of the shock absorber. What are the benefits after replacing the shock absorber? Buffer conveys shock to drivers and passengers in order to improve ride comfort and reduce fatigue. Extend body life, prevent spring damage and improve braking effect. Suppressing the rapid vibration of the wheels while driving, preventing the tires from leaving the road surface and improving the driving stability. Improving driving stability and adjustability, effectively conveying engine deflagration pressure to the ground, so as to save fuel costs. What happens if I do not replace worn out shocks and struts? Tires will wear out prematurely, the vehicle becomes more difficult to stop, steer and maintain tire contact with the road. The vehicle will be difficult to control and unpleasant to drive. The ability of the driver to make emergency maneuvers and stops is compromised. The complete strut assembly includes a new spring, strut mount, dust bellows, and bump stop. It is about 50% faster and much safer to install a complete strut assembly compared to a bare strut. Generally, a new strut mount, dust bellows, and bumper are needed with the bare strut replacement. So, the complete strut assembly saves time, is cheaper than the bare strut plus purchasing the replacement strut mount kit and is much safer to install. Why should I replace complete strut assembly in PAIR? It is generally recommended to replace shocks and struts in pairs for the front or rear of the vehicle. This practice ensures that the repair schedule for the left and ride sides are harmonized. Do not provide pick-up service. We have 2 warehouses in CA and GA, normally package will be dispatched from the one that is nearest to you. We specialize in aftermarket automotive car parts and is the #1 industry distributor for affordable and quality products. We have a complete staffing and professional designer team, our goal is to strive to become a first-class auto parts sales company. We not only have aftermartket parts to provide, we can also produce molds through our own design. Ensure product quality and increase product quantity Provide you with more options for accessories. Our company has several warehouses in the east, south, west and central United States, which can deliver goods to your quickly and on time. And we also provide more convenient and fast channels for after-sales processing of goods.